Each headlight has an 8 watt power consumption and light intensity of 4400 lumens
Optimal illumination of road surface due to wide light angle
Increased safety when riding at night
Housing made of plastic and black powder-coated aluminum

Very small design: 70mm x 61mm diameter
One lamp weighs 485 gramms

This article is needed to mount the case locking unit (CLU)

- Required for the Touring case set or Touring top case with "KTM RACE ON" (keyless) system
- Only one piece is needed per vehicle

This wiring harness is needed for the Touring case set or Touring top case with Race-on system.

This wiring harness is needed for installing the a heated ergo rider`s seat or a heated ergo pillion seat. If both parts will be mounted, still just 1 pcs. Of this wiring harness is needed.
Connects the seats to the HCU.

Control unit for adjusting the heated seat and heated grips through the combination switches and the dashboard.

WIRING HARNESS FOR SEAT HEATING (A62611986000) - Required

KTM ERGO RIDER'S SEAT - Required
(A62607940016C1A) same height
(A62607940018C1A) Higher
(A62607940014C1A) Lower

High-quality look
Integrate perfectly into the vehicle design
Modern and simple design
Plug & Play mounting
Increased safety due to extremely bright flashing light
Visual highlight

- Small design: width approx. 2 mm, length approx. 73 mm
- Contains 4 LED turn signals
- Make sure the latest version of the software is installed on the vehicle

Protects display from unwanted scratches and marks
Made of high-grade, anti-scratch material
Made from high quality tempered glass

Protects display from unwanted scratches and marks
Made of high-grade, anti-scratch material
Made from high quality tempered glass

Plug & Play mounting
Waterproof switch
Optimal protection against stone impact

Separate start- & stop switch which can easily plugged in the main wiring harness.
Functional cover made of textile fabric to protect the wire from damage and soiling.

An absolute must for every ambitious biker
Substantial weight saving
Tested in complex and specially-developed test cycles
Perfect for use on the race track
Plug & Play mounting
Unbeatable cost/weight saving ratio
Mountable in any position, as it does not contains acid
Safe technology and long life

Technical data:
12,8 V maintenance-free LiFePo4-battery
Capacity 8.0 Ah

Recommended charging current - 4.0 amps
Maximum charge current for fast charging - 32 amps

An absolute must for every ambitious biker
Substantial weight saving
Tested in complex and specially-developed test cycles
Perfect for use on the race track
Plug & Play mounting
Unbeatable cost/weight saving ratio
Mountable in any position, as it does not contains acid
Safe technology and long life

Technical data:
12,8 V maintenance-free LiFePo4-battery
Capacity 6.0 Ah

Recommended charging current - 3.0 amps
Maximum charge current for fast charging - 24 amps

Can be installed in the standard headlight mask
Increased safety when riding at night

High-quality look
Integrate perfectly into the vehicle design
Modern and simple design
Visual highlight
Plug & Play mounting

Increased safety due to extremely bright flashing light
Small design: width approx. 20 mm, length approx. 73 mm
Contains 2 LED turn signals

High-quality look
Integrate perfectly into the vehicle design
Modern and simple design
Visual highlight
Plug & Play mounting
Increased safety due to extremely bright flashing light

Small design: width approx. 20 mm, length approx. 73 mm
Contains 2 LED turn signals with integrated rear and brake light
Make sure the latest version of the software is installed on the vehicle

High-quality look
Integrate perfectly into the vehicle design
Modern and simple design
Visual highlight
Plug & Play mounting
Increased safety due to extremely bright flashing light

Small design: width approx. 20 mm, length approx. 73 mm
Contains 4 LED turn signals: 2 pcs. for the front and 2 pcs. with integrated rear and brake light for the rear

Recommended article: License plate holder support (A60708915044)